Birdhouse Hole Size Drill-Bit Checker: Inches to Millimetres

Does your drill bit match the birdhouse entrance hole specified for your target bird? Choose a North American cavity-nesting species from Cornell Lab’s NestWatch placement table, enter a nominal round drill bit diameter in millimetres or inches, and see the difference from the documented round-hole target. The calculator checks exact unit conversion, nominal diameter difference and circular opening-area change; it does not claim a near match is wildlife-safe, advise drilling larger to admit a species, or replace a complete nest box plan.

Birdhouse hole diameter and drill-bit checker

This calculator covers round entrances only. Some species have alternative ovals, slots or crescent openings; those have two distinct dimensions and cannot be safely replaced by a single circle calculated from the area. Select only a bird that naturally nests in an appropriate cavity box in your region, and confirm NestWatch’s full species and habitat requirements before building.

1. Choose the species and its reference hole

Automatically filled from NestWatch when a species is selected. Choose Custom to enter a different documented round-hole target.

Switch to the full species plan if the entrance is not round. This checker does not convert a slot into a circle.

2. Check the actual drill, hole saw or measured opening

A listed nominal size is not a verified physical size; check your own drill/bit and measure the finished hole.





Documented round entrance diameter28.575 mm

1 1/8 in (1.1250 decimal inches)

Entered cutter / measured hole28.575 mm

1.1250 decimal inches

Signed diameter difference0.000 mm

Positive means larger than the documented round hole. Negative means smaller.

Calculated circular opening-area change0.0%

Geometric change only: never a predicted passage, predator or nesting-success percentage.

The entered nominal diameter matches the reference number exactly. This is not a completed-box safety certification.

The two circles are schematic and share a scale with each other, not with your physical screen. The image is not a print-at-100%-scale cutting template. Never use its pixel size to mark a hole.

Complete reference chart from the selectable NestWatch examples

Representative round-hole sizes taken from Cornell Lab NestWatch’s nest box placement table, not a universal listing for every bird
SpeciesRound hole (inches)Exact metric conversionWhy the full plan matters

The chart deliberately excludes oval-only species such as Wood Duck. Some other listed birds also have oval alternatives not represented here. The tool does not predict which birds will actually enter a box.

Printable entrance-hole measurement notes

Change your selected species or bit to update the summary.

Calculations take place in the browser and do not submit your measurements to OwlRatings.

Important before cutting: If the hole is larger or smaller than the reference size, do not assume it is an acceptable substitute because it looks close in millimetres. Find the correct cutter or an appropriate manufacturer-approved entrance guard and verify the finished hole. Hole position, cavity depth, drainage, ventilation, predator protection and location are equally important. Never cut, enlarge or cover the opening of an occupied nest box without qualified legal and wildlife guidance.

JavaScript is disabled. Use the reference table and exact inch–millimetre conversions in the article below.


Birdhouse hole sizes in millimetres and inches

The correct entrance hole is one of the most important dimensions in a functional birdhouse. An opening that is too small can exclude your intended species; a larger opening may admit other birds or predators and undermine the protection offered by a species-specific design. But hole diameter is not enough by itself. The floor, depth, mounting position, local habitat, ventilation, drainage, predator guards and maintenance all need to match the target species. Cornell Lab’s NestWatch nest box placement table gives round-hole dimensions alongside habitat, height and minimum spacing for many North American cavity nesters.

For an entrance drilled as a circle, this calculator treats one international inch as exactly 25.4 mm. A 1 1/8-inch hole therefore equals precisely 28.575 mm, a 1 3/8-inch hole is 34.925 mm, and a 1 1/2-inch hole is 38.100 mm. Those are exact unit conversions of the nominal published dimensions, not a claim that every drill bit or finished hole can be manufactured to the nearest thousandth of a millimetre.

Common round entrance sizes and metric conversions, following selected NestWatch species recommendations
Nominal round holeExact diameter in mmExamples from Cornell NestWatchDesign limitation
1 inch25.400 mmHouse WrenFollow wren-specific box and habitat requirements
1 1/8 inch28.575 mmBlack-capped and Carolina ChickadeesDo not assume all regions or cavity designs are identical
1 1/4 inch31.750 mmTufted Titmouse; White-breasted and Red-breasted NuthatchesHouse Sparrow competition can be a concern
1 3/8 inch34.925 mmTree Swallow; Violet-green SwallowHabitat, box placement and competitors differ by region
1 1/2 inch38.100 mmEastern and Western Bluebirds (round alternative)Eastern Bluebird also has a documented oval entrance option
1 9/16 inch39.688 mm (rounded)Mountain BluebirdLarger opening may increase competitor access
2 1/2 inch63.500 mmNorthern FlickerRequires a different large cavity-box design
3 inches76.200 mmEastern Screech-Owl (round alternative)Large species-specific box, height and mounting requirements

These are round-hole examples rather than a universal chart for every cavity bird. Cornell also lists oval or slotted entrances for some species, such as Eastern Bluebird (2 1/4 inches tall by 1 3/8 inches wide as an alternative) and Wood Duck (4 inches wide by 3 inches high). A round drill cannot reproduce those shapes just by matching their area. Always follow the intended plan rather than trying to convert an oval to a circular diameter.

How to use the drill-bit checker before building a birdhouse

  1. Choose your intended nesting species. Verify it actually occurs and nests in boxes in your area, and review the habitat and other construction dimensions before buying materials.
  2. Check the documented round hole. The dropdown uses Cornell NestWatch’s species placement table. If your build uses an alternative oval or crescent plan, choose the non-round option; the calculator will stop rather than produce an inappropriate circle.
  3. Enter the cutter you actually have. Choose millimetres or inches and enter the tool’s stated nominal size, or use a provided common fractional-inch preset. Do not treat a preset as proof that your physical bit is correctly labeled or manufactured.
  4. Read the signed difference. The tool shows how much larger or smaller the entered number is than the published target, in millimetres and inches. A non-zero result receives a caution, not approval.
  5. Measure the real finished hole. A damaged bit, flexible material, worn hole saw, rough edges or drilling technique can change the final opening. The size printed on the tool is not guaranteed to be the achieved hole size.
  6. Check the whole box and the law. Do not alter an occupied nest box casually. Confirm habitat, predator protection and timing with Cornell NestWatch or your local wildlife agency.

Worked example: a chickadee’s 1 1/8-inch entrance

For Black-capped Chickadee, Cornell NestWatch lists a 1 1/8-inch round entrance, exactly 28.575 mm. Suppose you have a 29 mm drill bit. Its numeric diameter is 29 − 28.575 = +0.425 mm larger than the NestWatch target. If both openings were perfect circles, the 29 mm circle would have about 3.0% more area. That area percentage is a mathematical comparison, not a measure of whether birds or predators can enter or a statement that the larger bit is safe.

With a 28 mm cutter, the numeric difference is −0.575 mm, and the circular area would be approximately 4.0% smaller. The tool warns in both cases. Do not assume that either metric substitute is appropriate simply because the difference looks small on paper. Find a documented alternative from an authoritative species-specific plan, or use the accurately specified cutter and verify the finished opening. The OwlRatings chickadee nest box guide covers the related box positioning considerations.

Worked example: Eastern Bluebird’s round entrance

For Eastern Bluebird, Cornell’s placement chart gives a 1 1/2-inch round hole (38.100 mm) or a 2 1/4-inch-high by 1 3/8-inch-wide oval in an appropriate alternate design. If your available cutter is a 38 mm hole saw, the diameter is numerically 0.100 mm smaller than the 38.100 mm round standard. The checker’s small-difference message does not authorize substituting a tool, since the finished opening may differ further. Verify the specific approved nest-box plan and actual cut, rather than claiming that all visually similar holes are acceptable.

The bluebird example also illustrates why the entire box plan matters. An Eastern Bluebird house in open habitat is not identical to a chickadee house in wooded habitat. Proper drainage, ventilation, placement height, predator guards and competition management can be more consequential than a decimal-inch conversion. See Where to Put an Eastern Bluebird House and Birdhouse Hole Size Guide by Species.

Exact inch-to-millimetre conversion does not certify a drill bit

The equation is simple: millimetres = inches × 25.4, and inches = millimetres ÷ 25.4. The conversion is exact by definition, but a real hole can be imperfect. Wood grain, sawdust, the cutting tool’s geometry and wear, wobble, how the hole is sanded, and a separate metal entrance plate can all influence its useful opening. A rough or splintered cut can also injure birds, so finish the entrance safely according to the manufacturer’s woodworking recommendations.

Importantly, the calculator does not choose “the nearest metric bit” as a safe recommendation. If you need a 31.750 mm nominal entrance and have a 32.000 mm tool, the computed difference is 0.250 mm. That does not establish that 32 mm is safe for a Tufted Titmouse or nuthatch. The correct response is to check the full trusted plan, source the specified tool and measure the resulting opening.

Why opening area changes faster than diameter

The area of a round hole is π × diameter² ÷ 4. If a hole’s diameter changes from 28.575 mm to 29 mm, its area grows in proportion to (29 ÷ 28.575)². That yields about 3.0% more circular area, not 1.5%. A 1 mm change on a small hole is a larger proportional difference than a 1 mm change on a very large hole. But cross-sectional area is not a biological model of bird passage. Actual bird dimensions, behavior, wing position, age, and the presence of competitors or predators cannot be reduced to a single area equation.

The diagram beside the calculator is drawn at the same relative scale for the target and entered circle, so the differences can be seen side by side. It is not a print-to-scale stencil. Phone screens, printers and CSS scaling differ; cutting a hole from an on-screen circle would be misleading. Use calibrated measuring tools and the official plan’s marked dimensions.

Can a smaller birdhouse entrance keep out House Sparrows or starlings?

Only under certain circumstances, and never as a complete guarantee. Cornell’s NestWatch guidance on House Sparrows and European Starlings explains that House Sparrows can enter holes as small as 1 1/4 inches, so many cavity-nesting songbirds’ boxes remain vulnerable. Its starling guidance also warns that larger entrances can permit invasive competitors. Do not assume a specific tiny rounding adjustment will exclude a species; actual openings and bird behavior vary.

Predator protection requires other design choices too. An appropriately mounted pole and purpose-built predator baffle can protect a box from climbing mammals better than relying only on a small round hole. If squirrels chew the opening larger, OwlRatings’ guide to preventing squirrels from enlarging holes discusses protective metal entrance plates and when repairs should be undertaken. Do not place added guards across an occupied entrance or make unplanned modifications to a nest in use.

Oval, slot and crescent entrances need a separate plan

Some NestWatch birds use openings that are not circular. A Wood Duck box uses a large horizontal oval around 4 × 3 inches, and a Purple Martin house may use a crescent-style alternative. Cornell also lists a 2 1/4 × 1 3/8-inch oval alternative for Eastern Bluebird. These shapes are designed with specific width and height relationships, sometimes affecting which species can pass through and whether nestlings can exit.

There is no one diameter that perfectly substitutes for those two dimensions. A circle with the same area as an oval does not have the same width or height. For any non-round entrance, refer to Cornell’s species-specific drawings or a relevant local wildlife agency’s approved plan; the checker intentionally blocks its round-hole calculations when a user selects an oval or slot.

Entrance diameter is only one part of a safe nest box

A complete nest box must provide appropriate interior floor dimensions, depth from entrance to floor, roof overhang, ventilation, drainage, secure mounting and predator-resistant construction. Cornell provides species-specific advice for nesting habitat and box placement, while OwlRatings explains the tradeoffs in Best Birdhouse Materials and Do Birdhouses Need Ventilation and Drainage Holes?.

For a cut-list rather than a hole-size decision, use the Nest Box Cut List Calculator, which plans lumber and saw kerf for a specific six-piece plan. The drill checker and cut-list tool answer separate questions: how to compare a round entrance with the documented diameter, versus how much stock is needed for the example construction. Neither tells you where to mount a box or whether a proposed opening is safe for every species.

Do not alter an occupied nest box

An active nest may be protected by law, and changing its entrance could injure young birds, separate parents from a clutch or interfere with the nest’s normal use. Do not drill, sand, replace the panel, install a restrictor or attach a cover to a box while birds are nesting without expert wildlife advice and any legal authorization needed. If the box is already occupied by an unwanted competitor, check lawful local management guidance; do not improvise harmful traps or block animals inside.

For responsible monitoring practices, consult How to Monitor a Nest Box Without Disturbing the Birds and Cornell’s NestWatch placement guidance. For general design, avoid unnecessary exterior perches, provide escape-friendly interior surfaces where appropriate and use predator protection matched to the mounting context.

Safe woodworking checks before using a hole saw or bit

  1. Confirm the exact hole and full plan. Check species, round versus oval shape, location of hole above the floor and whether a plate or guard is included in the design.
  2. Choose the correct tool for the material. Hole saws, Forstner bits and other tools have different operating requirements. Use only a tool rated for the drill and workpiece.
  3. Secure the workpiece and wear appropriate protection. Clamp the wood, follow the tool manufacturer’s instructions and use eye and hearing protection as required. Avoid loose clothing or reaching into moving tools.
  4. Check for damage and rough edges. A ragged entry can injure a nesting bird. Measure and finish safely before assembling the box.
  5. Leave active nests undisturbed. Make construction corrections before the box is occupied; consult a wildlife authority if an occupied box appears unsafe.

Printable workshop conversion worksheet

Write your actual species, official plan and measured finished entrance, not just a guess from the tool label
Species and referenceOfficial round hole (in / mm)Nominal toolMeasured final holeAction needed before installing?
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________

Frequently asked questions

What drill bit makes a 1 1/8-inch birdhouse hole?

A nominal 1 1/8-inch cutter corresponds to 28.575 mm. For example, Cornell NestWatch lists this as the round hole diameter for Black-capped Chickadee. Check the tool’s intended cut, clamp and drill safely, and measure the finished opening rather than assuming a size label guarantees the actual hole.

Is 29 mm the same as 1 1/8 inches?

No. 1 1/8 in = 28.575 mm exactly, so 29 mm is 0.425 mm larger. The difference in perfect circular area is about 3.0%. That is not a scientific approval or rejection threshold for nesting birds: follow the documented plan, not the nearest metric drill by default.

What hole size does an Eastern Bluebird house need?

According to Cornell NestWatch’s placement table, a round entrance can be 1 1/2 inches (38.1 mm); it also lists an oval alternative at 2 1/4 inches high by 1 3/8 inches wide. Different box plans may differ, so follow your chosen full design and local wildlife recommendations.

What is the correct round entrance for a House Wren?

Cornell’s current Nest Box Placement table lists 1 inch (25.4 mm) for House Wren. Some older generic charts may show another size; consult the specific species plan and do not automatically use a larger opening.

Should I enlarge a chickadee hole to accommodate bluebirds?

Not casually. Chickadee and bluebird boxes differ in more than hole diameter. First determine the target species, the habitat and whether the entire box construction is suitable. Never enlarge an occupied nest box or alter active nesting habitat without qualified advice.

What if my drill bit is 0.1 mm smaller than the documented hole?

The checker shows the exact numeric difference but does not authorize that substitution. The actual finished cut, tool tolerances, shape and official construction plan determine what is appropriate. Use a specified tool or a documented alternative rather than treating decimal closeness as an ecological safety margin.

Does a larger birdhouse hole automatically attract more birds?

No. It can admit unwanted competitors or predators, and it may undermine the species-specific function of the box. Nest success depends on habitat, box design, height, predator protection, clean construction and local conditions, not just how large the opening looks.

Can I print the diagram and use it as a drilling template?

No. Screen and printer scaling vary, so the graphic is not dimensionally calibrated. Use a measured cutter and a trusted full-scale construction plan or verified physical ruler instead.

Does OwlRatings record which species or hole size I enter?

No. The calculations run in your browser tab without an account or submission to OwlRatings. You may copy, print or export a CSV record for your own workshop notes.

Sources and editorial methodology

Original methodology, November 2026: This browser-only checker uses nominal round-hole diameters recorded in the currently reviewed Cornell NestWatch placement table; exact metric conversion uses 25.4 mm per inch. It calculates signed nominal diameter difference = entered mm − target mm and circular opening-area difference = ((entered diameter ÷ reference diameter)² − 1) × 100%. An absolute difference below 0.05 mm is treated as a decimal-conversion match only, never as manufacturing tolerance, a safe wildlife adjustment or predicted animal-passage likelihood. Diagram circles share an internal relative scale but are not physical templates. Alternative oval and non-round entrances are intentionally blocked. The tool does not model actual hole roughness, bird anatomy, competitor passage, species range, predator safety, laws, wood quality or nesting outcomes. It cannot check whether a cutter or target is appropriate for a particular full species design. Check updated NestWatch guidance and local conservation rules before cutting. No user inputs are uploaded, and all examples are instructional, not first-hand testing. Report corrections via OwlRatings contact.

Similar Posts